1 files changed, 11 insertions, 11 deletions

diff --git a/documentation/sdk-manual/working-projects.rst b/documentation/sdk-manual/working-projects.rst
index beec1dd09a..9a0db0099d 100644
--- a/documentation/sdk-manual/working-projects.rst
+++ b/documentation/sdk-manual/working-projects.rst
@@ -31,7 +31,7 @@ project:
    GNOME Developer
    site.
 
-1. *Create a Working Directory and Populate It:* Create a clean
+#. *Create a Working Directory and Populate It:* Create a clean
    directory for your project and then make that directory your working
    location::
 
@@ -74,7 +74,7 @@ project:
          bin_PROGRAMS = hello
          hello_SOURCES = hello.c
 
-2. *Source the Cross-Toolchain Environment Setup File:* As described
+#. *Source the Cross-Toolchain Environment Setup File:* As described
    earlier in the manual, installing the cross-toolchain creates a
    cross-toolchain environment setup script in the directory that the
    SDK was installed. Before you can use the tools to develop your
@@ -92,7 +92,7 @@ project:
 
       $ source tmp/deploy/images/qemux86-64/environment-setup-core2-64-poky-linux
 
-3. *Create the configure Script:* Use the ``autoreconf`` command to
+#. *Create the configure Script:* Use the ``autoreconf`` command to
    generate the ``configure`` script::
 
       $ autoreconf
@@ -108,7 +108,7 @@ project:
       which ensures missing auxiliary files are copied to the build
       host.
 
-4. *Cross-Compile the Project:* This command compiles the project using
+#. *Cross-Compile the Project:* This command compiles the project using
    the cross-compiler. The
    :term:`CONFIGURE_FLAGS`
    environment variable provides the minimal arguments for GNU
@@ -129,7 +129,7 @@ project:
 
      $ ./configure --host=armv5te-poky-linux-gnueabi --with-libtool-sysroot=sysroot_dir
 
-5. *Make and Install the Project:* These two commands generate and
+#. *Make and Install the Project:* These two commands generate and
    install the project into the destination directory::
 
       $ make
@@ -149,7 +149,7 @@ project:
 
       $ file ./tmp/usr/local/bin/hello
 
-6. *Execute Your Project:* To execute the project, you would need to run
+#. *Execute Your Project:* To execute the project, you would need to run
    it on your target hardware. If your target hardware happens to be
    your build host, you could run the project as follows::
 
@@ -227,7 +227,7 @@ established through the script::
 To illustrate variable use, work through this simple "Hello World!"
 example:
 
-1. *Create a Working Directory and Populate It:* Create a clean
+#. *Create a Working Directory and Populate It:* Create a clean
    directory for your project and then make that directory your working
    location::
 
@@ -266,7 +266,7 @@ example:
              printf("\n");
          }
 
-2. *Source the Cross-Toolchain Environment Setup File:* As described
+#. *Source the Cross-Toolchain Environment Setup File:* As described
    earlier in the manual, installing the cross-toolchain creates a
    cross-toolchain environment setup script in the directory that the
    SDK was installed. Before you can use the tools to develop your
@@ -284,7 +284,7 @@ example:
 
       $ source tmp/deploy/images/qemux86-64/environment-setup-core2-64-poky-linux
 
-3. *Create the Makefile:* For this example, the Makefile contains
+#. *Create the Makefile:* For this example, the Makefile contains
    two lines that can be used to set the :term:`CC` variable. One line is
    identical to the value that is set when you run the SDK environment
    setup script, and the other line sets :term:`CC` to "gcc", the default
@@ -302,7 +302,7 @@ example:
         rm -rf *.o
         rm target_bin
 
-4. *Make the Project:* Use the ``make`` command to create the binary
+#. *Make the Project:* Use the ``make`` command to create the binary
    output file. Because variables are commented out in the Makefile, the
    value used for :term:`CC` is the value set when the SDK environment setup
    file was run::
@@ -387,7 +387,7 @@ example:
    use the SDK environment variables regardless of the values in the
    Makefile.
 
-5. *Execute Your Project:* To execute the project (i.e. ``target_bin``),
+#. *Execute Your Project:* To execute the project (i.e. ``target_bin``),
    use the following command::
 
       $ ./target_bin