7 files changed, 0 insertions, 193 deletions

diff --git a/meta-poky/conf/local.conf.sample b/meta-poky/conf/local.conf.sample
index 2e0bb41e64..b555f1d21e 100644
--- a/meta-poky/conf/local.conf.sample
+++ b/meta-poky/conf/local.conf.sample
@@ -31,7 +31,6 @@
 #MACHINE ?= "beaglebone-yocto"
 #MACHINE ?= "genericx86"
 #MACHINE ?= "genericx86-64"
-#MACHINE ?= "mpc8315e-rdb"
 #MACHINE ?= "edgerouter"
 #
 # This sets the default machine to be qemux86-64 if no other machine is selected:
diff --git a/meta-yocto-bsp/README.hardware b/meta-yocto-bsp/README.hardware
index d8d2a0cac6..5996be764c 100644
--- a/meta-yocto-bsp/README.hardware
+++ b/meta-yocto-bsp/README.hardware
@@ -28,7 +28,6 @@ Hardware Reference Boards
 The following boards are supported by the meta-yocto-bsp layer:
 
   * Texas Instruments Beaglebone (beaglebone-yocto)
-  * Freescale MPC8315E-RDB (mpc8315e-rdb)
   * Ubiquiti Networks EdgeRouter Lite (edgerouter)
   * General IA platforms (genericx86 and genericx86-64)
 
@@ -155,147 +154,6 @@ From a Linux system with access to the image files perform the following steps:
 
   3. Insert the SD card into the Beaglebone and boot the board.
 
-Freescale MPC8315E-RDB (mpc8315e-rdb)
-=====================================
-
-The MPC8315 PowerPC reference platform (MPC8315E-RDB) is aimed at hardware and
-software development of network attached storage (NAS) and digital media server
-applications. The MPC8315E-RDB features the PowerQUICC II Pro processor, which
-includes a built-in security accelerator.
-
-(Note: you may find it easier to order MPC8315E-RDBA; this appears to be the
-same board in an enclosure with accessories. In any case it is fully
-compatible with the instructions given here.)
-
-Setup instructions
-------------------
-
-You will need the following:
-* NFS root setup on your workstation
-* TFTP server installed on your workstation
-* Straight-thru 9-conductor serial cable (DB9, M/F) connected from your 
-  PC to UART1
-* Ethernet connected to the first ethernet port on the board
-
---- Preparation ---
-
-Note: if you have altered your board's ethernet MAC address(es) from the
-defaults, or you need to do so because you want multiple boards on the same
-network, then you will need to change the values in the dts file (patch
-linux/arch/powerpc/boot/dts/mpc8315erdb.dts within the kernel source). If
-you have left them at the factory default then you shouldn't need to do
-anything here.
-
-Note: To boot from USB disk you need u-boot that supports 'ext2load usb'
-command. You need to setup TFTP server, load u-boot from there and
-flash it to NOR flash.
-
-Beware! Flashing bootloader is potentially dangerous operation that can
-brick your device if done incorrectly. Please, make sure you understand
-what below commands mean before executing them.
-
-Load the new u-boot.bin from TFTP server to memory address 200000
-=> tftp 200000 u-boot.bin
-
-Disable flash protection
-=> protect off all
-
-Erase the old u-boot from fe000000 to fe06ffff in NOR flash.
-The size is 0x70000 (458752 bytes)
-=> erase fe000000 fe06ffff
-
-Copy the new u-boot from address 200000 to fe000000
-the size is 0x70000. It has to be greater or equal to u-boot.bin size
-=> cp.b 200000 fe000000 70000
-
-Enable flash protection again
-=> protect on all
-
-Reset the board
-=> reset
-
---- Booting from USB disk ---
-
- 1. Flash partitioned image to the USB disk
-
-    # dd if=core-image-minimal-mpc8315e-rdb.wic of=/dev/sdb
-
- 2. Plug USB disk into the MPC8315 board
-
- 3. Connect the board's first serial port to your workstation and then start up
-    your favourite serial terminal so that you will be able to interact with
-    the serial console. If you don't have a favourite, picocom is suggested:
-
-  $ picocom /dev/ttyUSB0 -b 115200
-
- 4. Power up or reset the board and press a key on the terminal when prompted
-    to get to the U-Boot command line
-
- 5. Optional. Load the u-boot.bin from the USB disk:
-
- => usb start
- => ext2load usb 0:1 200000 u-boot.bin
-
-    and flash it to NOR flash as described above.
-
- 6. Load the kernel and dtb from the first partition of the USB disk:
-
- => usb start
- => ext2load usb 0:1 1000000 uImage
- => ext2load usb 0:1 2000000 dtb
-
- 7. Set bootargs and boot up the device
-
- => setenv bootargs root=/dev/sdb2 rw rootwait console=ttyS0,115200
- => bootm 1000000 - 2000000
-
-
---- Booting from NFS root ---
-
-Load the kernel and dtb (device tree blob), and boot the system as follows:
-
- 1. Get the kernel (uImage-mpc8315e-rdb.bin) and dtb (uImage-mpc8315e-rdb.dtb)
-    files from the tmp/deploy directory, and make them available on your TFTP
-    server.
-
- 2. Connect the board's first serial port to your workstation and then start up
-    your favourite serial terminal so that you will be able to interact with
-    the serial console. If you don't have a favourite, picocom is suggested:
-
-  $ picocom /dev/ttyUSB0 -b 115200
-
- 3. Power up or reset the board and press a key on the terminal when prompted
-    to get to the U-Boot command line
-
- 4. Set up the environment in U-Boot:
-
- => setenv ipaddr <board ip>
- => setenv serverip <tftp server ip>
- => setenv bootargs root=/dev/nfs rw nfsroot=<nfsroot ip>:<rootfs path> ip=<board ip>:<server ip>:<gateway ip>:255.255.255.0:mpc8315e:eth0:off console=ttyS0,115200
-
- 5. Download the kernel and dtb, and boot:
-
- => tftp 1000000 uImage-mpc8315e-rdb.bin
- => tftp 2000000 uImage-mpc8315e-rdb.dtb
- => bootm 1000000 - 2000000
-
---- Booting from JFFS2 root ---
-
- 1. First boot the board with NFS root.
-
- 2. Erase the MTD partition which will be used as root:
-
-    $ flash_eraseall  /dev/mtd3
-
- 3. Copy the JFFS2 image to the MTD partition:
-
-    $ flashcp core-image-minimal-mpc8315e-rdb.jffs2 /dev/mtd3
-
- 4. Then reboot the board and set up the environment in U-Boot:
-
-    => setenv bootargs root=/dev/mtdblock3 rootfstype=jffs2 console=ttyS0,115200
-
-
 Ubiquiti Networks EdgeRouter Lite (edgerouter)
 ==============================================
 
diff --git a/meta-yocto-bsp/conf/machine/mpc8315e-rdb.conf b/meta-yocto-bsp/conf/machine/mpc8315e-rdb.conf
deleted file mode 100644
index 5382796284..0000000000
--- a/meta-yocto-bsp/conf/machine/mpc8315e-rdb.conf
+++ /dev/null
@@ -1,36 +0,0 @@
-#@TYPE: Machine
-#@NAME: Freescale MPC8315E-RDB
-#@DESCRIPTION: Machine configuration for Freescale MPC8315E-RDB
-
-TARGET_FPU = ""
-
-require conf/machine/include/tune-ppce300c3.inc
-
-KERNEL_IMAGETYPE = "uImage"
-
-EXTRA_IMAGEDEPENDS += "u-boot"
-UBOOT_MACHINE = "MPC8315ERDB_config"
-
-SERIAL_CONSOLES = "115200;ttyS0"
-
-MACHINE_FEATURES = "keyboard pci ext2 ext3 serial"
-
-PREFERRED_VERSION_linux-yocto ?= "5.2%"
-PREFERRED_PROVIDER_virtual/kernel ?= "linux-yocto"
-
-PREFERRED_PROVIDER_virtual/xserver ?= "xserver-xorg"
-XSERVER ?= "xserver-xorg \
-            xf86-video-fbdev"
-
-UBOOT_ENTRYPOINT = "0x00000000"
-
-KERNEL_DEVICETREE = "mpc8315erdb.dtb"
-
-MACHINE_EXTRA_RRECOMMENDS = "kernel-modules"
-
-IMAGE_FSTYPES ?= "jffs2 tar.bz2"
-JFFS2_ERASEBLOCK = "0x4000"
-
-IMAGE_FSTYPES += "wic wic.bmap"
-WKS_FILE ?= 'mpc8315e-rdb.wks'
-IMAGE_BOOT_FILES ?= "u-boot.bin uImage mpc8315erdb.dtb;dtb"
diff --git a/meta-yocto-bsp/recipes-kernel/linux/linux-yocto-dev.bbappend b/meta-yocto-bsp/recipes-kernel/linux/linux-yocto-dev.bbappend
index f044dafb4d..6e5a129dd4 100644
--- a/meta-yocto-bsp/recipes-kernel/linux/linux-yocto-dev.bbappend
+++ b/meta-yocto-bsp/recipes-kernel/linux/linux-yocto-dev.bbappend
@@ -2,7 +2,6 @@ KBRANCH_genericx86  = "standard/base"
 KBRANCH_genericx86-64  = "standard/base"
 KBRANCH_edgerouter = "standard/edgerouter"
 KBRANCH_beaglebone-yocto = "standard/beaglebone"
-KBRANCH_mpc8315e-rdb = "standard/fsl-mpc8315e-rdb"
 
 KMACHINE_genericx86 ?= "common-pc"
 KMACHINE_genericx86-64 ?= "common-pc-64"
@@ -12,4 +11,3 @@ COMPATIBLE_MACHINE_genericx86 = "genericx86"
 COMPATIBLE_MACHINE_genericx86-64 = "genericx86-64"
 COMPATIBLE_MACHINE_edgerouter = "edgerouter"
 COMPATIBLE_MACHINE_beaglebone-yocto = "beaglebone-yocto"
-COMPATIBLE_MACHINE_mpc8315e-rdb = "mpc8315e-rdb"
diff --git a/meta-yocto-bsp/recipes-kernel/linux/linux-yocto_4.19.bbappend b/meta-yocto-bsp/recipes-kernel/linux/linux-yocto_4.19.bbappend
index ec269d905c..7b4bd2c4ee 100644
--- a/meta-yocto-bsp/recipes-kernel/linux/linux-yocto_4.19.bbappend
+++ b/meta-yocto-bsp/recipes-kernel/linux/linux-yocto_4.19.bbappend
@@ -2,7 +2,6 @@ KBRANCH_genericx86  = "v4.19/standard/base"
 KBRANCH_genericx86-64  = "v4.19/standard/base"
 KBRANCH_edgerouter = "v4.19/standard/edgerouter"
 KBRANCH_beaglebone-yocto = "v4.19/standard/beaglebone"
-KBRANCH_mpc8315e-rdb = "v4.19/standard/fsl-mpc8315e-rdb"
 
 KMACHINE_genericx86 ?= "common-pc"
 KMACHINE_genericx86-64 ?= "common-pc-64"
@@ -12,16 +11,13 @@ SRCREV_machine_genericx86    ?= "5664dc14399edcaad210bbeb6343d84561fb3ea8"
 SRCREV_machine_genericx86-64 ?= "5664dc14399edcaad210bbeb6343d84561fb3ea8"
 SRCREV_machine_edgerouter ?= "5664dc14399edcaad210bbeb6343d84561fb3ea8"
 SRCREV_machine_beaglebone-yocto ?= "5664dc14399edcaad210bbeb6343d84561fb3ea8"
-SRCREV_machine_mpc8315e-rdb ?= "d419f4ca6ba4b097b8ad710a93b89510f5b2998c"
 
 COMPATIBLE_MACHINE_genericx86 = "genericx86"
 COMPATIBLE_MACHINE_genericx86-64 = "genericx86-64"
 COMPATIBLE_MACHINE_edgerouter = "edgerouter"
 COMPATIBLE_MACHINE_beaglebone-yocto = "beaglebone-yocto"
-COMPATIBLE_MACHINE_mpc8315e-rdb = "mpc8315e-rdb"
 
 LINUX_VERSION_genericx86 = "4.19.34"
 LINUX_VERSION_genericx86-64 = "4.19.34"
 LINUX_VERSION_edgerouter = "4.19.34"
 LINUX_VERSION_beaglebone-yocto = "4.19.34"
-LINUX_VERSION_mpc8315e-rdb = "4.19.34"
diff --git a/meta-yocto-bsp/recipes-kernel/linux/linux-yocto_5.2.bbappend b/meta-yocto-bsp/recipes-kernel/linux/linux-yocto_5.2.bbappend
index f15bccbaf2..9a965321df 100644
--- a/meta-yocto-bsp/recipes-kernel/linux/linux-yocto_5.2.bbappend
+++ b/meta-yocto-bsp/recipes-kernel/linux/linux-yocto_5.2.bbappend
@@ -2,7 +2,6 @@ KBRANCH_genericx86  = "v5.2/standard/base"
 KBRANCH_genericx86-64  = "v5.2/standard/base"
 KBRANCH_edgerouter = "v5.2/standard/edgerouter"
 KBRANCH_beaglebone-yocto = "v5.2/standard/beaglebone"
-KBRANCH_mpc8315e-rdb = "v5.2/standard/fsl-mpc8315e-rdb"
 
 KMACHINE_genericx86 ?= "common-pc"
 KMACHINE_genericx86-64 ?= "common-pc-64"
@@ -12,16 +11,13 @@ SRCREV_machine_genericx86    ?= "25b14cdf9659c68ab32d66616dfdbbe2ece3fd94"
 SRCREV_machine_genericx86-64 ?= "25b14cdf9659c68ab32d66616dfdbbe2ece3fd94"
 SRCREV_machine_edgerouter ?= "25b14cdf9659c68ab32d66616dfdbbe2ece3fd94"
 SRCREV_machine_beaglebone-yocto ?= "25b14cdf9659c68ab32d66616dfdbbe2ece3fd94"
-SRCREV_machine_mpc8315e-rdb ?= "77f031b182885c177b3a96098ae61271911a7954"
 
 COMPATIBLE_MACHINE_genericx86 = "genericx86"
 COMPATIBLE_MACHINE_genericx86-64 = "genericx86-64"
 COMPATIBLE_MACHINE_edgerouter = "edgerouter"
 COMPATIBLE_MACHINE_beaglebone-yocto = "beaglebone-yocto"
-COMPATIBLE_MACHINE_mpc8315e-rdb = "mpc8315e-rdb"
 
 LINUX_VERSION_genericx86 = "5.2.17"
 LINUX_VERSION_genericx86-64 = "5.2.17"
 LINUX_VERSION_edgerouter = "5.2.17"
 LINUX_VERSION_beaglebone-yocto = "5.2.17"
-LINUX_VERSION_mpc8315e-rdb = "5.2.17"
diff --git a/meta-yocto-bsp/wic/mpc8315e-rdb.wks b/meta-yocto-bsp/wic/mpc8315e-rdb.wks
deleted file mode 100644
index d0cb607ffc..0000000000
--- a/meta-yocto-bsp/wic/mpc8315e-rdb.wks
+++ /dev/null
@@ -1,4 +0,0 @@
-# short-description: Create SD card image for MPC8315E-RDB
-# long-description: Create a partitioned SD card image for Freescale MPC8315E-RDB reference hardware.
-part /boot --source bootimg-partition --ondisk sdb --fstype=ext3 --label boot
-part / --source rootfs --ondisk sdb --fstype=ext3 --label root