linux/meta-xilinx.git/conf/machine/boards/zedboard/zedboard-zynq7-board.dtsi, branch fidoMirror of git.yoctoproject.org/meta-xilinx.githttps://git.enea.com/cgit/linux/meta-xilinx.git/atom?h=fido2015-04-21T04:12:42+00:00zynq7-base.dtsi: Update bindings for PHYs attached to ethernet nodes2015-04-21T04:12:42+00:00Nathan Rossinathan.rossi@xilinx.com2015-04-21T04:12:42+00:00urn:sha1:965b8e54c45b60e9d346178c8285552c3d70c28d
* Update the bindings to match upstream definitions for the PHY
* The macb driver does not follow the phy-handle property and relies on
the PHY being located as the first child node of the ethernet device
* Remove the MDIO node and update all boards to nest the PHY as the
first child node of the ethernet device, this change is backward
compatible with the bindings for the linux-xlnx xemacps driver which
follows the phy-handle definition
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
boards/*-board.dtsi: Added USB PHY nodes for USB reset2015-04-17T05:50:26+00:00Nathan Rossinathan.rossi@xilinx.com2015-04-17T05:50:26+00:00urn:sha1:cfacbc9f19b9778eceda3f7ef51419ab70ebc4ac
* Added information about the GPIO/MIO reset pin so that the USB can be
reset by the kernel
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
boards/*.dtsi: Fix up USB PHY reset nodes2014-11-04T03:52:53+00:00Nathan Rossinathan.rossi@xilinx.com2014-11-04T03:45:07+00:00urn:sha1:3bbc21f9f1e2d2980a459d76cc2385ce6417ea46
* Use the xlnx,phy-reset-gpio property to specify the USB PHY's reset
signal
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
boards/*.dtsi: Updated Zynq device trees2014-10-31T08:18:52+00:00Nathan Rossinathan.rossi@xilinx.com2014-10-31T08:18:52+00:00urn:sha1:589e95ca85ff7378a778ef27bd9d52c72aab2e67
* Removed use of very outdated 'gpio-mask-high' and 'gpio-mask-low'
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
zedboard-zynq7: Fixed up device tree2014-10-31T07:22:33+00:00Nathan Rossinathan.rossi@xilinx.com2014-10-31T07:22:33+00:00urn:sha1:ffa9c0f7425916527c5f75c9e6b9610a9415ca12
* Added USB PHY reset binding
* Updated Ethernet PHY compat and init values
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
zynq7-base.dtsi: Update bindings2014-05-26T06:26:59+00:00Nathan Rossinathan.rossi@xilinx.com2014-05-26T06:26:59+00:00urn:sha1:56afae038a1c5a8165371cd295ab50ba2400efd8
* Update QSPI, SPI, devcfg and GPIO node bindings
* Flash node properties for boards
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
machine: Fix inclusion of dtsi's for *-yocto devicetrees2014-04-07T08:01:10+00:00Nathan Rossinathan.rossi@xilinx.com2014-04-07T08:01:10+00:00urn:sha1:ee5920bec14133d427f09f75b32cae355d436d6e
* Fix inclusion of zynq-7-mainline-gem.dtsi so that nodes properties in
the board level are not overwritten
* Add the *-yocto.dts to the machine configurations
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
zedboard-zynq7: Cleaned up device trees and configuration2014-03-12T07:48:33+00:00Nathan Rossinathan.rossi@xilinx.com2014-03-12T07:48:33+00:00urn:sha1:62d1fde75f96445025522c8739971d40d9c1c6b9
* Cleaned up device trees, refactored the dts per boot args setup
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>