1 files changed, 10 insertions, 20 deletions

diff --git a/documentation/sdk-manual/appendix-obtain.rst b/documentation/sdk-manual/appendix-obtain.rst
index 3c1dc52d19..0ce828aa29 100644
--- a/documentation/sdk-manual/appendix-obtain.rst
+++ b/documentation/sdk-manual/appendix-obtain.rst
@@ -25,8 +25,7 @@ Follow these steps to locate and hand-install the toolchain:
    download the installer appropriate for your build host, target
    hardware, and image type.
 
-   The installer files (``*.sh``) follow this naming convention:
-   ::
+   The installer files (``*.sh``) follow this naming convention::
 
       poky-glibc-host_system-core-image-type-arch-toolchain[-ext]-release.sh
 
@@ -55,15 +54,13 @@ Follow these steps to locate and hand-install the toolchain:
 
    For example, if your build host is a 64-bit x86 system and you need
    an extended SDK for a 64-bit core2 target, go into the ``x86_64``
-   folder and download the following installer:
-   ::
+   folder and download the following installer::
 
       poky-glibc-x86_64-core-image-sato-core2-64-toolchain-ext-&DISTRO;.sh
 
 4. *Run the Installer:* Be sure you have execution privileges and run
    the installer. Following is an example from the ``Downloads``
-   directory:
-   ::
+   directory::
 
       $ ~/Downloads/poky-glibc-x86_64-core-image-sato-core2-64-toolchain-ext-&DISTRO;.sh
 
@@ -132,8 +129,7 @@ build the SDK installer. Follow these steps:
       using to build the installer. If
       SDKMACHINE
       is not set appropriately, the build fails and provides an error
-      message similar to the following:
-      ::
+      message similar to the following::
 
               The extensible SDK can currently only be built for the same architecture as the machine being built on - SDK_ARCH is
               set to i686 (likely via setting SDKMACHINE) which is different from the architecture of the build machine (x86_64).
@@ -144,8 +140,7 @@ build the SDK installer. Follow these steps:
    SDK and populate the SDK image, use the following command form. Be
    sure to replace image with an image (e.g. "core-image-sato"): $
    bitbake image -c populate_sdk You can do the same for the extensible
-   SDK using this command form:
-   ::
+   SDK using this command form::
 
       $ bitbake image -c populate_sdk_ext
 
@@ -170,8 +165,7 @@ build the SDK installer. Follow these steps:
          libc-staticdev"
 
 7. *Run the Installer:* You can now run the SDK installer from
-   ``tmp/deploy/sdk`` in the Build Directory. Following is an example:
-   ::
+   ``tmp/deploy/sdk`` in the Build Directory. Following is an example::
 
       $ cd poky/build/tmp/deploy/sdk
       $ ./poky-glibc-x86_64-core-image-sato-core2-64-toolchain-ext-&DISTRO;.sh
@@ -211,8 +205,7 @@ Follow these steps to extract the root filesystem:
    which you can use with QEMU directly.
 
    The pre-built root filesystem image files follow these naming
-   conventions:
-   ::
+   conventions::
 
       core-image-profile-arch.tar.bz2
 
@@ -233,8 +226,7 @@ Follow these steps to extract the root filesystem:
 
    For example, if you plan on using a BeagleBone device as your target
    hardware and your image is a ``core-image-sato-sdk`` image, you can
-   download the following file:
-   ::
+   download the following file::
 
       core-image-sato-sdk-beaglebone-yocto.tar.bz2
 
@@ -246,8 +238,7 @@ Follow these steps to extract the root filesystem:
    installed the toolchain (e.g. ``poky_sdk``).
 
    Following is an example based on the toolchain installed in the
-   ":ref:`sdk-manual/appendix-obtain:locating pre-built sdk installers`" section:
-   ::
+   ":ref:`sdk-manual/appendix-obtain:locating pre-built sdk installers`" section::
 
       $ source poky_sdk/environment-setup-core2-64-poky-linux
 
@@ -258,8 +249,7 @@ Follow these steps to extract the root filesystem:
    from a previously built root filesystem image that was downloaded
    from the :yocto_dl:`Index of Releases </releases/yocto/yocto-&DISTRO;/machines/>`.
    This command extracts the root filesystem into the ``core2-64-sato``
-   directory:
-   ::
+   directory::
 
       $ runqemu-extract-sdk ~/Downloads/core-image-sato-sdk-beaglebone-yocto.tar.bz2 ~/beaglebone-sato