dev-manual, ref-manual: Systemd-boot: Update documents for new EFI bootloader

Fixes [YOCTO #9707]

* Replaced gummiboot with systemd-boot in the dev-manual
* Replaced the gummiboot class with a new systemd-boot class
* Replaced the appropriate gummiboot variables in the glossary
  with new variables SYSTEMD_BOOT_CFG, SYSTEMD_BOOT_ENTRIES,
  and SYSTEMD_BOOT_TIMEOUT.

(From yocto-docs rev: 778b620e65cc68531b3c41aeb8f27f2a07eb0d00)

Signed-off-by: Scott Rifenbark <srifenbark@gmail.com>
Signed-off-by: Richard Purdie <richard.purdie@linuxfoundation.org>

1 files changed, 13 insertions, 13 deletions

diff --git a/documentation/dev-manual/dev-manual-common-tasks.xml b/documentation/dev-manual/dev-manual-common-tasks.xml
index 48d3ecb632..bd11062c41 100644
--- a/documentation/dev-manual/dev-manual-common-tasks.xml
+++ b/documentation/dev-manual/dev-manual-common-tasks.xml
@@ -8777,19 +8777,19 @@
                             within a separately started QEMU or any
                             other virtual machine manager.
                             </para></listitem>
-                        <listitem><para><emphasis>"GummibootTarget":</emphasis>
-                            Choose "GummibootTarget" if your hardware is
+                        <listitem><para><emphasis>"Systemd-bootTarget":</emphasis>
+                            Choose "Systemd-bootTarget" if your hardware is
                             an EFI-based machine with
-                            <filename>gummiboot</filename> as bootloader and
+                            <filename>systemd-boot</filename> as bootloader and
                             <filename>core-image-testmaster</filename>
                             (or something similar) is installed.
                             Also, your hardware under test must be in a
                             DHCP-enabled network that gives it the same IP
                             address for each reboot.</para>
-                            <para>If you choose "GummibootTarget", there are
+                            <para>If you choose "Systemd-bootTarget", there are
                             additional requirements and considerations.
                             See the
-                            "<link linkend='selecting-gummiboottarget'>Selecting GummibootTarget</link>"
+                            "<link linkend='selecting-systemd-boottarget'>Selecting Systemd-bootTarget</link>"
                             section, which follows, for more information.
                             </para></listitem>
                         <listitem><para><emphasis>"BeagleBoneTarget":</emphasis>
@@ -8835,12 +8835,12 @@
                 </para>
             </section>
 
-            <section id='selecting-gummiboottarget'>
-                <title>Selecting GummibootTarget</title>
+            <section id='selecting-systemd-boottarget'>
+                <title>Selecting Systemd-bootTarget</title>
 
                 <para>
                     If you did not set <filename>TEST_TARGET</filename> to
-                    "GummibootTarget", then you do not need any information
+                    "Systemd-bootTarget", then you do not need any information
                     in this section.
                     You can skip down to the
                     "<link linkend='qemu-image-running-tests'>Running Tests</link>"
@@ -8849,14 +8849,14 @@
 
                 <para>
                     If you did set <filename>TEST_TARGET</filename> to
-                    "GummibootTarget", you also need to perform a one-time
+                    "Systemd-bootTarget", you also need to perform a one-time
                     setup of your master image by doing the following:
                     <orderedlist>
                         <listitem><para><emphasis>Set <filename>EFI_PROVIDER</filename>:</emphasis>
                             Be sure that <filename>EFI_PROVIDER</filename>
                             is as follows:
                             <literallayout class='monospaced'>
-     EFI_PROVIDER = "gummiboot"
+     EFI_PROVIDER = "systemd-boot"
                             </literallayout>
                             </para></listitem>
                         <listitem><para><emphasis>Build the master image:</emphasis>
@@ -8920,7 +8920,7 @@
 
                 <para>
                     The final thing you need to do when setting
-                    <filename>TEST_TARGET</filename> to "GummibootTarget" is
+                    <filename>TEST_TARGET</filename> to "Systemd-bootTarget" is
                     to set up the test image:
                     <orderedlist>
                         <listitem><para><emphasis>Set up your <filename>local.conf</filename> file:</emphasis>
@@ -8929,7 +8929,7 @@
                             <literallayout class='monospaced'>
      IMAGE_FSTYPES += "tar.gz"
      INHERIT += "testimage"
-     TEST_TARGET = "GummibootTarget"
+     TEST_TARGET = "Systemd-bootTarget"
      TEST_TARGET_IP = "192.168.2.3"
                             </literallayout>
                             </para></listitem>
@@ -9325,7 +9325,7 @@
                                     The target controller object used to deploy
                                     and start an image on a particular target
                                     (e.g. QemuTarget, SimpleRemote, and
-                                    GummibootTarget).
+                                    Systemd-bootTarget).
                                     Tests usually use the following:
                                     <itemizedlist>
                                         <listitem><para><emphasis><filename>ip</filename>:</emphasis>