1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
|
From 4004c3e68b973f4cb736048b1e90ee3b511f5865 Mon Sep 17 00:00:00 2001
From: Koen Kooi <koen@beagleboard.org>
Date: Wed, 12 Jan 2011 00:23:29 +0000
Subject: [PATCH 03/28] omap3: beaglexm: fix power on of DVI
TFP410 DVI chip is used to provide display out.
This chip is controlled by 2 lines:
LDO which supplies the power is controlled over gpio + 2
and the enable of the chip itself is done over gpio + 1
NOTE: the LDO is necessary for LED, serial blocks as well.
gpio + 1 was used to sense USB overcurrent in vanilla beagle.
Without this fix, the display would not function as the LDO
remains shut down.
[nm@ti.com: split up, added descriptive changelogs]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Koen Kooi <koen@beagleboard.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
---
arch/arm/mach-omap2/board-omap3beagle.c | 42 ++++++++++++++++++++++++++++--
1 files changed, 39 insertions(+), 3 deletions(-)
diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c
index 673deb9..2ed8040 100644
--- a/arch/arm/mach-omap2/board-omap3beagle.c
+++ b/arch/arm/mach-omap2/board-omap3beagle.c
@@ -273,6 +273,8 @@ static struct gpio_led gpio_leds[];
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
+ int r;
+
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
mmc[0].gpio_wp = -EINVAL;
} else if ((omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_C1_3) ||
@@ -293,9 +295,16 @@ static int beagle_twl_gpio_setup(struct device *dev,
/* REVISIT: need ehci-omap hooks for external VBUS
* power switch and overcurrent detect
*/
-
- gpio_request(gpio + 1, "EHCI_nOC");
- gpio_direction_input(gpio + 1);
+ if (omap3_beagle_get_rev() != OMAP3BEAGLE_BOARD_XM) {
+ r = gpio_request(gpio + 1, "EHCI_nOC");
+ if (!r) {
+ r = gpio_direction_input(gpio + 1);
+ if (r)
+ gpio_free(gpio + 1);
+ }
+ if (r)
+ pr_err("%s: unable to configure EHCI_nOC\n", __func__);
+ }
/*
* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
@@ -316,6 +325,33 @@ static int beagle_twl_gpio_setup(struct device *dev,
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
+ /*
+ * gpio + 1 on Xm controls the TFP410's enable line (active low)
+ * gpio + 2 control varies depending on the board rev as follows:
+ * P7/P8 revisions(prototype): Camera EN
+ * A2+ revisions (production): LDO (supplies DVI, serial, led blocks)
+ */
+ if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
+ r = gpio_request(gpio + 1, "nDVI_PWR_EN");
+ if (!r) {
+ r = gpio_direction_output(gpio + 1, 0);
+ if (r)
+ gpio_free(gpio + 1);
+ }
+ if (r)
+ pr_err("%s: unable to configure nDVI_PWR_EN\n",
+ __func__);
+ r = gpio_request(gpio + 2, "DVI_LDO_EN");
+ if (!r) {
+ r = gpio_direction_output(gpio + 2, 1);
+ if (r)
+ gpio_free(gpio + 2);
+ }
+ if (r)
+ pr_err("%s: unable to configure DVI_LDO_EN\n",
+ __func__);
+ }
+
return 0;
}
--
1.6.6.1
|